| Author |
 Topic  |
|
|
topgeargames
Canada
27 Posts |
 Posted - 07/08/2013 : 23:04:19
|
| The GQ-4X supports most of the Macronix branded chips, but it doesnt have the MX29F1610 listed. It is pinout compatible with the MX29L3211 chip (minus the A20 pin), so is there something I can add to the device.txt to add support for this chip? |
|
| Reply #1
ZLM
2947 Posts |
Posted - 07/10/2013 : 18:53:20
|
Yes. You can try:
Name="MX29L1610T*PSOP44",ID="C261",Class="MX29L3211",CodeSize="2097152",Category="FLASH",MFG="Macronix",Adapter="ADP-019 V3",VCC="3.6V",RVpp="5V",TempUnprotect="Yes,False",Platform="GQ-4X",Message="Set the adapter to 5V jumper position. Jumper on 29L3211 positions";
Name="MX29L1610B*PSOP44",ID="C262",Class="MX29L3211",CodeSize="2097152",Category="FLASH",MFG="Macronix",Adapter="ADP-019 V3",VCC="3.6V",RVpp="5V",TempUnprotect="Yes,False",Platform="GQ-4X",Message="Set the adapter to 5V jumper position. Jumper on 29L3211 positions";
|
 |
|
| Reply #2
Bad_Ad84
210 Posts |
Posted - 07/14/2013 : 22:46:56
|
He said MX29F1610 not the MX29L161
The 29F161 is a 5v chip, not 3.6 |
|
|
| Reply #3
ZLM
2947 Posts |
Posted - 07/15/2013 : 09:55:15
|
Try:
Name="MX29F1610T*PSOP44",ID="C2FA",Class="MX29L3211",CodeSize="2097152",Category="FLASH",MFG="Macronix",Adapter="ADP-019 V4",VCC="5V",RVpp="5V",TempUnprotect="Yes,False",Platform="GQ-4X",Message="Set the adapter to 5V jumper position. J2 on 28F, J1 on 29LV160 positions";
Name="MX29F1610B*PSOP44",ID="C2FB",Class="MX29L3211",CodeSize="2097152",Category="FLASH",MFG="Macronix",Adapter="ADP-019 V4",VCC="5V",RVpp="5V",TempUnprotect="Yes,False",Platform="GQ-4X",Message="Set the adapter to 5V jumper position.J2 on 28F, J1 on 29LV160 positions"; |
|
|
| Reply #4
goul-patrol
19 Posts |
Posted - 01/25/2014 : 07:03:44
|
is it good for id and config ?
h**p://hpics.li/9d1c6d9
you can see :
Manufacturer Code : C2H
MX29F1610 Device Code : F1H
i have error erase .
|
Edited by - goul-patrol on 01/25/2014 07:06:42 |
|
|
| Reply #5
goul-patrol
19 Posts |
Posted - 01/25/2014 : 07:28:33
|
Name="MX29F1610T*PSOP44",ID="C2F1",
with this id are correct but config not ! |
|
|
| Reply #6
ZLM
2947 Posts |
Posted - 01/25/2014 : 20:43:28
|
| What config? Can you read it? |
|
|
| Reply #7
goul-patrol
19 Posts |
Posted - 01/26/2014 : 02:07:55
|
i want burn MX 29f1610MC i have adaptor adp-019 v4
i take this:
Name="MX29F1610T*PSOP44",ID="C2F1",Class="MX29L3211",CodeSize="2097152",Category="FLASH",MFG="Macronix",Adapter="ADP-019 V4",VCC="5V",RVpp="5V",TempUnprotect="Yes,False",Platform="GQ-4X",Message="Set the adapter to 5V jumper position. J2 on 28F, J1 on 29LV160 positions";
But it's not good the j2 on 28f return unkown id, but j2 on 32l return the good id .
i think j1 on 29lv160 is not good , because i have no erase and no prog ? |
|
|
| Reply #8
goul-patrol
19 Posts |
Posted - 01/27/2014 : 00:45:42
|
| nobody can reply the good way on gq4x with adaptor adp-019 v4 to burn Mx29f1610mc ? |
|
|
| Reply #9
ZLM
2947 Posts |
|
| Reply #10
goul-patrol
19 Posts |
Posted - 01/28/2014 : 02:38:54
|
| i try it and give you the result ;) |
|
|
| Reply #11
goul-patrol
19 Posts |
Posted - 01/28/2014 : 23:02:56
|
hello,
with usbprog6.27 the id is good i have make the wiring :
http://www.mcumall.com/support/MX29F1610_OnV4.jpg
but prog and erase are not good :( i think the pinout is not good some one can tell me the j1 and j2 exactelly rewire . |
|
|
| Reply #12
ZLM
2947 Posts |
Posted - 01/28/2014 : 23:36:27
|
does read work?
check the Temp Unprotect checkbox.
Image Insert:
4.06 KB |
|
|
| Reply #13
goul-patrol
19 Posts |
Posted - 01/29/2014 : 02:40:30
|
i haven't this this part of sofware are blank ?
i have windows 7 pro 64 bit the software give me the good hardware rev and software but i think i have bug how to make a cleaning intall remove all and reinstall it ? |
|
|
| Reply #14
ZLM
2947 Posts |
Posted - 01/29/2014 : 09:52:13
|
It should always there.
No, you do not need to reinstall, this checkbox will be enabled after you select the chip from the device list. |
|
|
| Reply #15
goul-patrol
19 Posts |
Posted - 01/29/2014 : 14:18:09
|
i have tested on other pc with windows xp 32 bit
with the temp unprotected checkbox
usbprog6.27 i have make the wiring :
http://www.mcumall.com/support/MX29F1610_OnV4.jpg
id is good but no prog no erase ... |
Edited by - goul-patrol on 01/29/2014 14:18:35 |
|
|
| Reply #16
ZLM
2947 Posts |
Posted - 01/29/2014 : 14:25:20
|
| Well, I thnk I need a testing chip in order to find out why. |
|
|
| Reply #17
goul-patrol
19 Posts |
|
| Reply #18
ZLM
2947 Posts |
Posted - 01/29/2014 : 17:00:49
|
Yes. I read that, the only difference is the Pin 44. The MX29F1610 Pin 44 is WP- and it needs to be connected to the VCC of the chip when erase and write.
Other than that, all commands and pins are same.
Therotically it should work. Since your test fail, so I need a chip to find out why.
You can still try to connect that chip pin 44 to the VCC 5V pin on adapter and see if it makes different.
The picture is connect the Pin 44 to the programmer WP pin. |
|
|
| Reply #19
goul-patrol
19 Posts |
Posted - 01/31/2014 : 16:11:13
|
| i have try it pin 44 to VCC 5 v no result :( |
|
|
| Reply #20
goul-patrol
19 Posts |
Posted - 04/15/2014 : 11:38:02
|
| have you some news ? |
|
|
| Reply #21
goul-patrol
19 Posts |
Posted - 05/24/2014 : 08:39:31
|
| some news for it ????????????????? |
|
|
| Reply #22
goul-patrol
19 Posts |
Posted - 06/28/2014 : 00:53:43
|
| harf no MX29F1610 on the new software 6,29 :) |
|
|
| Reply #23
goul-patrol
19 Posts |
Posted - 07/01/2014 : 13:25:18
|
Hello,
Can I caress the soft dream that one day close enough my problem is a solution, support this software eprom level? |
|
|
| Reply #24
goul-patrol
19 Posts |
Posted - 07/05/2014 : 03:18:00
|
| it would still be nice to have an answer as what the problem is treated |
|
|
| Reply #25
goul-patrol
19 Posts |
Posted - 11/06/2014 : 04:24:52
|
have You some news ?
for the MX29F1610. |
|
|
| Reply #26
ramparts
7 Posts |
Posted - 01/26/2015 : 18:06:43
|
One thing i notice is when you put the 29lv160 adapter it tells to active the 5 volt ,but you can see that the chip i am using the 29lv160tmc-90 is a 3.0-3.6v chip so how the programmer tells me to activate the 5volt jumper on the adapter?
With the 5v active reads but donґt write ,meanwhile i will try to set 3.3v jumper to see if i can program the chip.
see datasheet:
h**p://pdf1.alldatasheet.com/datasheet-pdf/view/74522/MCNIX/MX29LV160TMC-90.html |
|
|
| Reply #27
ZLM
2947 Posts |
Posted - 01/27/2015 : 11:24:09
|
The 5V jumper on adapter means adapter has no control on VCC. The VCC controlled by programmer.
In this case, the programmer is going to adjust the VCC to 3.6V.
The 5V/3.6V VCC jumper on adapter has its story, it mainly for a backward compatibility design. The old Willem programmer has no automatic VCC control, all the voltages controlled by combination of jumpers, include the adapter VCC jumper.
The GQ-4X has automatic VCC control. So, it adjusts the VCC based on the chip voltage. But all adapters are compatible with old willem programmer.
|
|
|
| Reply #28
ramparts
7 Posts |
Posted - 01/27/2015 : 16:35:36
|
wELL i have a willem and i recently i bought a gq-4x ,strangely just the old dog true willem 4.5c has been efective on reading all tipes of chips,i had an usue that gq-4x didnґt read a clone chip of 27c4001 and the willem did maybe because of the code id ,if the programmer canґt detect a valid cod id from the manufacturer wonґt read the chip,i think that could be the cause.
i had bought a gq-4x serial adapter and this from the net
h**p://www.ebay.com/itm/PSOP44-V4-for-AM29LV160-MX29L3211-PSOP44-DIP44-programmer-adapter-converter-/221498913746?ssPageName=ADME:X:RTQ:US:1123
this till now seems a copy adapter for 29lv160 and i couldnґt get it to read neither one of my 10 new 29lv160tmc-90 chips.
what i mean is that in some cases the old hardware donґdisappoint ,and makes me wonder if is a good idea to spend about 60 euros on a new willem programmer.
Because you pay money and get bad results ,and in some cases low or no support..
Sory my bad english
Best Regards
JOSЙ |
|
|
| Reply #29
ZLM
2947 Posts |
|
| Reply #30
ramparts
7 Posts |
Posted - 01/31/2015 : 11:56:32
|
So basicaly an expensive Copy of the original 
they should have copied better 
They told they were go tho see what is wrong but i doubt ,i will put it work ok.
If the shipping cost werenґt so expensive for my country i would buy the official from McuMall 
thank you very much for your Help |
|
|
| Reply #31
RedScorpion
Germany
14 Posts |
Posted - 02/14/2015 : 02:26:13
|
hi guys,
maybe i find a way to solve this issue.
Ezoflash has a adapter which is almost the same lime the adp-19 from gqx4.
In this schematic he uses one 6k8 resistor to VCC to set the WP Pin to high i think.
Could anyone check this?!
Set the same settings from 29L3211 chip and solder a 6k8 resistor to VCC.
h**p://www.ezoflash.com/scriptdapters/psop44c1/schematic.htm
thanks
red |
|
|
| Reply #32
ramparts
7 Posts |
Posted - 02/14/2015 : 18:57:38
|
hi guys,
maybe i find a way to solve this issue.
Ezoflash has a adapter which is almost the same lime the adp-19 from gqx4.
In this schematic he uses one 6k8 resistor to VCC to set the WP Pin to high i think.
Could anyone check this?!
Set the same settings from 29L3211 chip and solder a 6k8 resistor to VCC.
h**p://www.ezoflash.com/scriptdapters/psop44c1/schematic.htm
thanks
red
Link not Available |
|
|
| Reply #33
RedScorpion
Germany
14 Posts |
|
| Reply #34
Rodragon
Brazil
3 Posts |
Posted - 01/02/2016 : 09:11:26
|
Any News about this?
Tryed all sollutions from the topic, but no success... |
|
|
| Reply #35
anniel
2596 Posts |
Posted - 01/02/2016 : 11:01:24
|
| Someone sent a chip to ZLM for testing? |
|
|
| Reply #36
Jarryson
Spain
10 Posts |
Posted - 05/27/2016 : 16:13:05
|
Hi,
where I have to set the 6k8 resistor? I want to read/write MX29L1610.
Regards. |
|
|
| Reply #37
anniel
2596 Posts |
Posted - 05/27/2016 : 16:49:47
|
| WP pin. |
|
|
| Reply #38
Jarryson
Spain
10 Posts |
Posted - 05/27/2016 : 18:15:27
|
quote:
Originally posted by anniel
WP pin.
I dont understand, sorry.
WP = Write Protect? what is this pin in the adapter adp 019?
Resistor have to go between 5V and WP ?
Thanks. |
Edited by - Jarryson on 05/27/2016 18:23:24 |
|
|
| Reply #39
anniel
2596 Posts |
Posted - 05/28/2016 : 03:32:34
|
Yes WP = Write Protect on your MX29L1610. Is your MX29L1610 5V?
You need to pull it high. |
|
|
| Reply #40
Jarryson
Spain
10 Posts |
Posted - 05/28/2016 : 05:31:29
|
quote:
Originally posted by anniel
Yes WP = Write Protect on your MX29L1610. Is your MX29L1610 5V?
You need to pull it high.
I havent tried it yet. But I dont understand, 6k8 between 5V and WP ? |
|
|
| Reply #41
anniel
2596 Posts |
|
| Reply #42
Rodragon
Brazil
3 Posts |
Posted - 07/14/2016 : 09:28:28
|
| So we have a solution for this? Can anyone post an image of the adapter ready to burn the 29F1610? |
|
|
| Reply #43
Ice Man
32 Posts |
Posted - 05/15/2017 : 03:54:15
|
| Any news for this? I'd like to program MX29F1610MC as well but it doesn't work. |
|
|
| Reply #44
kodyk17
5 Posts |
Posted - 07/20/2017 : 18:20:55
|
I'd like to know how this can be programmed on Willem GQ-4x I have an ADP-019 v4.1 adapter and MX29F1610-10 chips. I've tried using this device.
Name="MX29F1610T*PSOP44",ID="C2F1",Class="MX29L3211",CodeSize="2097152",Category="FLASH",MFG="Macronix",Adapter="ADP-019 V4",VCC="5V",RVpp="5V",TempUnprotect="Yes,False",Platform="GQ-4X",Message="Set the adapter to 5V jumper position. J2 on 28F, J1 on 29LV160 positions";
Can get chip to ID, ERASE, and Blank Check with J1 and J2 set for 29L3211. I connected a resistor between pin 44 (WP) to +5 on the adp adapter and I still cannot get it to write. Is there anyone that can help resolve this long running issue?
|
|
|
| Reply #45
kodyk17
5 Posts |
|
| Reply #46
Ice Man
32 Posts |
Posted - 02/16/2018 : 02:42:45
|
| Any news on this? |
|
|
| Reply #47
anniel
2596 Posts |
Posted - 02/16/2018 : 04:15:01
|
quote:
Originally posted by Ice Man
Any news on this?
Someone sent a chip to ZLM for testing? |
|
|
| Reply #48
Ice Man
32 Posts |
Posted - 02/16/2018 : 07:38:11
|
| Don't have any since I've been waiting for this chip to be supported. Even requested it via software long time ago but nothing was done yet. :( |
|
|
| Reply #49
22asd
USA
4 Posts |
Posted - 03/30/2019 : 21:29:55
|
Any news on this or is ZLM still waiting for donor chips?
|
|
|
| Reply #50
anniel
2596 Posts |
Posted - 03/31/2019 : 04:28:26
|
quote:
Originally posted by 22asd
Any news on this or is ZLM still waiting for donor chips?
You should give a call to MCUMall. |
|
|
| Reply #51
22asd
USA
4 Posts |
Posted - 04/01/2019 : 22:49:57
|
| Got that number? I assume that it has been resolved to some extent. There seems to be an addition of the chip to some extent as well as an image to show how to setup the adapter to flash it. Right? |
|
|
| Reply #52
anniel
2596 Posts |
Posted - 04/03/2019 : 03:56:21
|
quote:
Originally posted by 22asd
Got that number? I assume that it has been resolved to some extent. There seems to be an addition of the chip to some extent as well as an image to show how to setup the adapter to flash it. Right?
http://www.mcumall.com/store/index.php?route=information/contact |
|
|
| Reply #53
22asd
USA
4 Posts |
Posted - 04/06/2019 : 02:22:10
|
| Going to be burning some next, I will let you know how that goes. I dont think there will be any problems, Ill keep you posted. |
|
|
| Reply #54
anniel
2596 Posts |
Posted - 04/06/2019 : 02:52:08
|
quote:
Originally posted by 22asd
Going to be burning some next, I will let you know how that goes. I dont think there will be any problems, Ill keep you posted.
Good. Thank you. |
|
|
| Reply #55
22asd
USA
4 Posts |
Posted - 05/24/2019 : 20:46:38
|
Cant get it to burn..did everything it said
Image Insert:
63249 bytes
Image Insert:
44740 bytes |
|
|
| Reply #56
Bogdanval
Fyro Macedonia
35 Posts |
Posted - 04/23/2023 : 17:30:21
|
Where is moderator??
I'ts important.
Regards. |
|
|
| Reply #57
Bogdanval
Fyro Macedonia
35 Posts |
Posted - 04/23/2023 : 21:04:52
|
Can I contact Administration?
It is about advertisement on your website.
Thank. |
|
|
| Reply #58
anniel
2596 Posts |
Posted - 04/24/2023 : 06:11:58
|
quote:
Originally posted by Bogdanval
Where is moderator??
I'ts important.
Regards.
Right here. |
|
|
| Reply #59
anniel
2596 Posts |
|
| Reply #60
Bogdanval
Fyro Macedonia
35 Posts |
|
| |
Topic |
|
Support for MX29F1610
[/url]