MCUmall EPROM BIOS Chip Burner Forum
MCUmall EPROM BIOS Chip Burner Forum
Home | Profile | Register | Active Topics | Members | Search | FAQ
Username:
Password:
Save Password
Forgot your Password?

 All Forums
 MCUmall Forums
 Using The Enhanced/Dual power Willem Programmer
 Cant Burn
 New Topic  Reply to Topic
 Printer Friendly
Author Previous Topic Topic Next Topic  

scar

10 Posts

Posted - 01/04/2012 :  20:14:21  Show Profile  Reply with Quote
I am trying to burn a 27C010 32pin eprom, and in the program I keep on getting this

img404.imageshack.us/img404/647/willem.jpg

I have a 12v PSU connected and all that so it cant be the power, and I have the device securely connected, and the eprom is snug in the zif socket. The jumpers are set right and all that. I do not know what is wrong.

Edited by - scar on 01/04/2012 20:15:21
Reply #1

scar

10 Posts

Posted - 01/05/2012 :  14:55:47  Show Profile  Reply with Quote
I just noticed on the thing, ICSP is in red lettering and none of the other chips have that that I have checked. Am I missing something?
Go to Top of Page
Reply #2

ZLM

2934 Posts

Posted - 01/09/2012 :  10:07:34  Show Profile  Reply with Quote
Try to do a self testing, see if you can find anything:

http://www.mcumall.com/forum/topic.asp?TOPIC_ID=1097
Go to Top of Page
Reply #3

scar

10 Posts

Posted - 01/09/2012 :  14:05:11  Show Profile  Reply with Quote
It still says "Check Power and Connection"
Go to Top of Page
Reply #4

scar

10 Posts

Posted - 01/09/2012 :  16:20:14  Show Profile  Reply with Quote
The only light that wont power on on the burner is the VPP, the others light up and the power light is Orange.
Go to Top of Page
Reply #5

ZLM

2934 Posts

Posted - 01/22/2012 :  23:39:47  Show Profile  Reply with Quote
check the confirm the driver is installed. The driver only works WinXP or earlier version windows. Also, check the data cable is a good and correct.
Go to Top of Page
Reply #6

scar

10 Posts

Posted - 01/23/2012 :  14:41:59  Show Profile  Reply with Quote
I am running the driver in compatibility mode, on top of that I used it in Windows 7s XP mode thing, and got the same result.
Go to Top of Page
Reply #7

ZLM

2934 Posts

Posted - 02/03/2012 :  22:29:50  Show Profile  Reply with Quote
The dual power willem drivewr only works on XP or earlier version windows.
Go to Top of Page
Reply #8

scar

10 Posts

Posted - 02/05/2012 :  10:24:11  Show Profile  Reply with Quote
I have the hacked .dll to allow it to work on W7 64Bit. It starts up fine. I am going to do a test, I have a TSOP40 Adapter, and I will try and write a TSOP40 chip using the adapter.
Go to Top of Page
Reply #9

scar

10 Posts

Posted - 02/11/2012 :  11:17:42  Show Profile  Reply with Quote
I have it installed in XPmode which is virtualized Windows XP and its still giving me guff.
Go to Top of Page
Reply #10

scar

10 Posts

Posted - 02/21/2012 :  14:19:20  Show Profile  Reply with Quote
I tracked down an old Toshiba laptop running Windows 98 and installed the software, the hardware checksout except for the VPP light. I try to burn a chip (27C010) and it gives me this error message

Error at 0x00000A Chip= 0x00 buffer 0xFF
Go to Top of Page
Reply #11

scar

10 Posts

Posted - 02/21/2012 :  14:35:26  Show Profile  Reply with Quote
Ok, the Parallel port needed to be switched to EPP and it now writes chips. But I have normal eproms and it has no trouble writing to the same chip, I don't know if its burning right
Go to Top of Page
  Previous Topic Topic Next Topic  
 New Topic  Reply to Topic
 Printer Friendly
Jump To:
MCUmall EPROM BIOS Chip Burner Forum © Copyright 2003 - 2009 Mcumall Electronics Inc. Go To Top Of Page
Generated in 0.23 sec. Snitz Forums 2000