MCUmall EPROM BIOS Chip Burner Forum
MCUmall EPROM BIOS Chip Burner Forum
Home | Profile | Register | Active Topics | Members | Search | FAQ
Username:
Password:
Save Password
Forgot your Password?

 All Forums
 MCUmall Forums
 Automobile engine ECU, Immo, Air bag chip tunning
 immo read with willem, which adapter
 New Topic  Reply to Topic
 Printer Friendly
Author Previous Topic Topic Next Topic  

passuff

7 Posts

Posted - 09/01/2009 :  07:17:08  Show Profile  Reply with Quote
I trying to remove the immo from my afn Passat 3b. What i know ist that the data is stored over here....:




www.bilder-hochladen.net/files/7c44-2b-jpg.html
So i would like to know if i can read&write the 24c02 ic2 eprom with my willem usb. The problem is that i only have the plcc32 on my board, so i think i need an adaptor for it, dont i?
Where can i get it, especially in germany?
thnx
Reply #1

passuff

7 Posts

Posted - 09/01/2009 :  08:16:43  Show Profile  Reply with Quote
I think i need a SOP8 to DIP16 adapter... Where can i find it? Can i take anything i find or is it willem specific?
Go to Top of Page
Reply #2

ZLM

2928 Posts

Posted - 09/09/2009 :  08:24:10  Show Profile  Reply with Quote
Yes. You need adaper ADP-004:

http://www.mcumall.com/comersus/store/comersus_viewItem.asp?idProduct=3103

OR

ADP-032 SOIC16 SOP16 ZIF adapter
http://www.mcumall.com/comersus/store/comersus_viewItem.asp?idProduct=3203

OR

In circuit testclip:

http://www.mcumall.com/comersus/store/comersus_viewItem.asp?idProduct=4406

the In circuit programming may need some testing and it is depending on your board design.



Go to Top of Page
Reply #3

ricampr

Portugal
21 Posts

Posted - 02/23/2010 :  14:29:40  Show Profile  Reply with Quote
hello
what is the position of the eprom programmer or adapter?
thanks
Go to Top of Page
Reply #4

ZLM

2928 Posts

Posted - 02/24/2010 :  22:35:08  Show Profile  Reply with Quote
You need adaper ADP-004:
http://www.mcumall.com/comersus/store/comersus_viewItem.asp?idProduct=3103

The position on programmer ZIF is lower pin aligned. Same as DIP8 chip.
Go to Top of Page
Reply #5

ricampr

Portugal
21 Posts

Posted - 02/25/2010 :  05:35:20  Show Profile  Reply with Quote
I have this-ADP-032 SOIC16 SOP16 ZIF adapter
which the correct orientation (function properly)
thanks
Go to Top of Page
Reply #6

ZLM

2928 Posts

Posted - 02/28/2010 :  09:06:33  Show Profile  Reply with Quote
Align the adapter lower pin to ZIF lower pin. Align the chip lower pin into adapter.
The position on programmer ZIF is lower pin aligned. Same as DIP8 chip. Example, select M95080 fro mthe software, the software will show the position of the chip. The adapter with the chip should go same location.
Go to Top of Page
  Previous Topic Topic Next Topic  
 New Topic  Reply to Topic
 Printer Friendly
Jump To:
MCUmall EPROM BIOS Chip Burner Forum © Copyright 2003 - 2009 Mcumall Electronics Inc. Go To Top Of Page
Generated in 0.17 sec. Snitz Forums 2000