| T O P I C R E V I E W |
| theamberco |
Posted - 09/05/2023 : 10:17:17
I have the programmer GQ4X. and the rev. 1.4. and the software rev. 6.38.
I cant erase it I have the adpater HO1591, ADP-030 and HO3902 to PLCC. I tried several new chips and nothing changes.
I try to write to it and also I cant. Any ideas what I need or what I can do?. As I need to wirte a bin to it.
I get the following messages.
Function not supported or chip cannot be erased.
Error of written Address 0x00000000,buffer= 0x02 device= 0xFF. |
| 13 L A T E S T R E P L I E S (Newest First) |
| anniel |
Posted - 03/17/2024 : 07:35:20
quote:
Originally posted by devinchin
I've tried this also. Keep posting these kind of stuff.
What did you try exactly? |
| devinchin |
Posted - 03/15/2024 : 22:36:01
I've tried this also. Keep posting these kind of stuff. |
| anniel |
Posted - 09/13/2023 : 09:31:53
quote:
Originally posted by theamberco
I dont know they were given to me, where can I buy original ones?
https://www.mouser.mx/c/semiconductors/memory-ics/eprom/?q=AT27C512R&package%20%2F%20case=PLCC-32 |
| theamberco |
Posted - 09/12/2023 : 16:06:29
I dont know they were given to me, where can I buy original ones? |
| anniel |
Posted - 09/12/2023 : 07:24:01
quote:
Originally posted by theamberco
No, ID is wrong too. So all the 6 chips are bad?
Fakes. Were did you buy them? |
| theamberco |
Posted - 09/10/2023 : 19:51:50
No, ID is wrong too. So all the 6 chips are bad? |
| anniel |
Posted - 09/10/2023 : 05:24:53
quote:
Originally posted by theamberco
It does blanck check no problem but when I load the bin and start to wrote at 0% stops with that error I tried several chips the same. Any ideas?
ID is correct? |
| theamberco |
Posted - 09/09/2023 : 13:36:30
It does blanck check no problem but when I load the bin and start to wrote at 0% stops with that error I tried several chips the same. Any ideas? |
| theamberco |
Posted - 09/09/2023 : 11:00:55
Error of written Address 0x00000000,buffer= 0x02 device= 0xFF. |
| anniel |
Posted - 09/08/2023 : 07:32:47
quote:
Originally posted by theamberco
I have HO1591 (older number) that is 100% the same. it has the two diodes and the jumper for 3.3V or 5V, still dont read it.
What error message do you get when reading? |
| anniel |
Posted - 09/08/2023 : 07:31:38
quote:
Originally posted by theamberco
I cant erase it
OTP cannot be erased, that's normal.
quote:
Originally posted by theamberco
I tried several new chips and nothing changes.
New chips are blank, you can verify this with Blank Check.
quote:
Originally posted by theamberco
I try to write to it and also I cant.
What error message do you get?
|
| theamberco |
Posted - 09/07/2023 : 08:00:54
I have HO1591 (older number) that is 100% the same. it has the two diodes and the jumper for 3.3V or 5V, still dont read it. |
| anniel |
Posted - 09/06/2023 : 10:51:53
quote:
Originally posted by theamberco
I have the programmer GQ4X. and the rev. 1.4. and the software rev. 6.38.
I cant erase it I have the adpater HO1591, ADP-030 and HO3902 to PLCC. I tried several new chips and nothing changes.
I try to write to it and also I cant. Any ideas what I need or what I can do?. As I need to wirte a bin to it.
I get the following messages.
Function not supported or chip cannot be erased.
Error of written Address 0x00000000,buffer= 0x02 device= 0xFF.
You need ADP-006. |
