MCUmall EPROM BIOS Chip Burner Forum
MCUmall EPROM BIOS Chip Burner Forum
Home | Profile | Register | Active Topics | Members | Search | FAQ
Username:
Password:
Save Password
Forgot your Password?

 All Forums
 MCUmall Forums
 Using The Enhanced/Dual power Willem Programmer
 Can't burn SST27s512

Note: You must be registered in order to post a reply.
To register, click here. Registration is FREE!

Screensize:
UserName:
Password:
Format Mode:
Format: BoldItalicizedUnderlineStrikethrough Align LeftCenteredAlign Right Horizontal Rule Insert HyperlinkInsert EmailInsert Image Insert CodeInsert QuoteInsert List Spell Checker
   
Message:

* HTML is OFF
* Forum Code is ON
Smilies
Smile [:)] Big Smile [:D] Cool [8D] Blush [:I]
Tongue [:P] Evil [):] Wink [;)] Clown [:o)]
Black Eye [B)] Eight Ball [8] Frown [:(] Shy [8)]
Shocked [:0] Angry [:(!] Dead [xx(] Sleepy [|)]
Kisses [:X] Approve [^] Disapprove [V] Question [?]

   Insert an Image File
Check here to include your profile signature.
    

T O P I C    R E V I E W
singleslamhp Posted - 08/28/2007 : 17:18:23
I finally got my burner to test Ok and erase from searching and finding the Jumper settings, but now I am having problems burning. I do not get any errors. This is what happens. I set jumpers, test hardware... Hardware present. Erase chip with vertical jumper in place... Device erase OK. Blank test....device is empty.... Load Bin file... file loaded ok. Remove vertical jumper. Program and verify..... It goes through the red and the green bars and say's verifying chip at the bottom. This never goes away. I click on compare/verify under action and it say's verify OK. I try to use this chip in my car and it does not work. Blank test.... Device is empty. Every time! I wonder if it will work if I smash it? AAAAAHHHHHHHHHH! Please help!
12   L A T E S T    R E P L I E S    (Newest First)
paulek9 Posted - 11/12/2009 : 21:16:24
if thats for honda ecus need to ad an offset when burning to 8000 and ill work
singleslamhp Posted - 08/31/2007 : 18:21:04
Thanks for all the help! I finally figured it out. The offset hex need to be changed to 8000.
singleslamhp Posted - 08/31/2007 : 14:53:10
I just tried 2 more bins and neither worked. Also I know the ecu is good, because the stock chip works.
singleslamhp Posted - 08/31/2007 : 14:40:58
I've tried 3 different ones that are supposed to be stock bins, but I suppose all of them could be wrong. It does look like the chip is burning though, Right?
ZLM Posted - 08/31/2007 : 14:22:27
You got wrong bin file.
singleslamhp Posted - 08/31/2007 : 14:06:58
Ok. The size and checksum read as follows OXFFF OXB800. At the top of the Buffer page there is all kinds of numbers. Toward the bottom of the buffer page it changes to all F's. I think it might actually be burning the chip. I wonder if the bin is just wrong. The car starts, but throws a solid Cel and runs like crap.
ZLM Posted - 08/30/2007 : 21:51:45
If you only see all FF in buffer, and the checksum is 0x0000 then the buffer is empty. That is to say your bin file loaded is an blank file.
singleslamhp Posted - 08/30/2007 : 19:47:48
Yes, I can do a blank check and it is empty. What do you mean the buffer is empty. Do you mean the Bin file I loaded has no info in it. Sorry I'm new to this. What do I need to do with the buffer? I clicked on buffer at the bottom and it just shows a bunch of F's everywhere. By the way thanks for all the help so far.
ZLM Posted - 08/29/2007 : 19:39:35
The software is correct and you do not need to download software.

If programmed and verified, then the chip should be programmed correctly.

Can you do a blank check after the programmed and verified?

If the chip is blank, then most likely your buffer is empty.



singleslamhp Posted - 08/29/2007 : 16:38:38
Should I redownload the software? BTW I forgot to mention. If the chip is not in the programer it will still try to program and it will verify.
singleslamhp Posted - 08/29/2007 : 13:43:08
I have the Enhanced Dual power PCB 3.5. The software I'm using is PCB35 (.98D6)
ZLM Posted - 08/28/2007 : 23:45:57
What is your programmer version?
What is your software version you are used?

It seems something wrong with the software.

MCUmall EPROM BIOS Chip Burner Forum © Copyright 2003 - 2009 Mcumall Electronics Inc. Go To Top Of Page
Generated in 0.08 sec. Snitz Forums 2000