MCUmall EPROM BIOS Chip Burner Forum
MCUmall EPROM BIOS Chip Burner Forum
Home | Profile | Register | Active Topics | Members | Search | FAQ
Username:
Password:
Save Password
Forgot your Password?

 All Forums
 MCUmall Forums
 Using The Enhanced/Dual power Willem Programmer
 help programing AM29f040B

Note: You must be registered in order to post a reply.
To register, click here. Registration is FREE!

Screensize:
UserName:
Password:
Format Mode:
Format: BoldItalicizedUnderlineStrikethrough Align LeftCenteredAlign Right Horizontal Rule Insert HyperlinkInsert EmailInsert Image Insert CodeInsert QuoteInsert List Spell Checker
   
Message:

* HTML is OFF
* Forum Code is ON
Smilies
Smile [:)] Big Smile [:D] Cool [8D] Blush [:I]
Tongue [:P] Evil [):] Wink [;)] Clown [:o)]
Black Eye [B)] Eight Ball [8] Frown [:(] Shy [8)]
Shocked [:0] Angry [:(!] Dead [xx(] Sleepy [|)]
Kisses [:X] Approve [^] Disapprove [V] Question [?]

   Insert an Image File
Check here to include your profile signature.
    

T O P I C    R E V I E W
alsauto Posted - 02/01/2006 : 14:17:39
I have just purchased a dual power programer, I am trying to program a AM29F040B chip but I keep getting an error at 0x0001a8 chip=0xe5.
when i erase this chip it goes to about 12% then says erase completed by check DQ7, when i do a blank test it tells me the chip is blank. one time it programed all the way but when i read the chip it is empty. I have tried 5 different chips 4 different computers, when i test hardware the vpp is getting 12vots, vcc is 5volts. the vcc led comes on when i erase and try to program, the red led does not light at all except for when i first turn the computer on then it goes out after I start EPROM3. the jumpers and dips are set as it shows in the software. I am chosing the M29F040B from the device menu as i do not see a choise for Am29F040B. the bios is set for ecp/epp have also tried ecp did not make a difference. any help would be appriecated. Thank You
4   L A T E S T    R E P L I E S    (Newest First)
alsauto Posted - 02/02/2006 : 14:44:43
i believe you are correct that i have prtocted sectors, when i read then check the buffer everything is FFFFFFFFFFFFF I try to unprotect the sectors by using the device menu unprotectAM29040 then the proper die number and following the correct steps but when i get to up protect sectors i click the button then get error (device code mismatch). when id is clicked in unprotect sectors, 00000-0ffff is 1A and all the rest say FF so i am assuming that those are protected but i cannot unprotect any ideas.
Thanks
alsauto Posted - 02/02/2006 : 08:56:58
I have tried all the different software versions still can not program, the chip does id ok, reads ok, erases ok. does anybody have any idea what i should try next.
Thanks
backbiter17 Posted - 02/02/2006 : 01:07:00
try to erase with 0.97g SW
when programing use 0.97a SW chose device 39f040 it worked for me some time ago
br, ales
ZLM Posted - 02/01/2006 : 15:24:26
Your setting and connection seems fine. The erase is working since you can do blank check. The chip only uses 5V Vcc, so it's nothing to do with the 12V Vpp.

Can you get ID correctly?

MCUmall EPROM BIOS Chip Burner Forum © Copyright 2003 - 2009 Mcumall Electronics Inc. Go To Top Of Page
Generated in 0.05 sec. Snitz Forums 2000