MCUmall EPROM BIOS Chip Burner Forum
MCUmall EPROM BIOS Chip Burner Forum
Home | Profile | Register | Active Topics | Members | Search | FAQ
Username:
Password:
Save Password
Forgot your Password?

 All Forums
 MCUmall Forums
 Using The Enhanced/Dual power Willem Programmer
 another sst27sf512 + dual not working

Note: You must be registered in order to post a reply.
To register, click here. Registration is FREE!

Screensize:
UserName:
Password:
Format Mode:
Format: BoldItalicizedUnderlineStrikethrough Align LeftCenteredAlign Right Horizontal Rule Insert HyperlinkInsert EmailInsert Image Insert CodeInsert QuoteInsert List Spell Checker
   
Message:

* HTML is OFF
* Forum Code is ON
Smilies
Smile [:)] Big Smile [:D] Cool [8D] Blush [:I]
Tongue [:P] Evil [):] Wink [;)] Clown [:o)]
Black Eye [B)] Eight Ball [8] Frown [:(] Shy [8)]
Shocked [:0] Angry [:(!] Dead [xx(] Sleepy [|)]
Kisses [:X] Approve [^] Disapprove [V] Question [?]

   Insert an Image File
Check here to include your profile signature.
    

T O P I C    R E V I E W
ronald55555 Posted - 08/08/2007 : 09:47:16
I have a willem dual power, 0.97ja, sst27sf512(brand new), correct cable that came with the burner, I cant erase nor burn.
I've followed the following jumper settings.

DIP 3 5 7 8 9 on(as in the pic in the program)
VPP jumper on bottom 2(normal)
jumpers set for pcb3b
JP1 and JP2 set at normal for when i try to read or burn
extra jumper on JP1 for erase
The 2 jumpers set at 12V(normal)
The jumper under that at 5V
using ac adapter, with jumper set accordingly




I've tried 5 different chips bought from xenocron, so it's unlikely all of them are bad. I also followed the instruction on xenocron
http://www.xenocron.com/install/Willem-SST.htm

Here's what i've tried:
start with a fresh chip, erase(with jumper in), pops up the "set jumper for W......", i hit ok, bar goes to 100%, says erase ok on the bottom. But when i do a blank check, it fails. I tried to burn it anyway, I unplugged everything, close problem, remove one of the jumper from JP1, load bin, hit burn, bar goes to 100%, but it gives me an error on the bottom offset0x0000.

I've also tried burning a brand new chip without trying to erase first, same error.

After i try to erase, I hit read, and looked at the buffer and it was not all FF, even though it said erase ok. so the blank check is right. I also tried to read a brand new chip, and it was not empty neither.

I also tried the test H/W tab and mesured the voltage according to instructons i found on another site, dont remember the exact numbers, but they were fine.

Anyone has any clue what's wrong?
1   L A T E S T    R E P L I E S    (Newest First)
ronald55555 Posted - 08/08/2007 : 09:49:31
forgot to mention, the lights light up fine, VPP and Power on, program would come on when i try to read erase or burn.

I tried to burn at offset 8000

also tried 0.98d6 w/ the 2 jumpers set at pcb3.5, same problems.

MCUmall EPROM BIOS Chip Burner Forum © Copyright 2003 - 2009 Mcumall Electronics Inc. Go To Top Of Page
Generated in 0.06 sec. Snitz Forums 2000