MCUmall EPROM BIOS Chip Burner Forum
MCUmall EPROM BIOS Chip Burner Forum
Home | Profile | Register | Active Topics | Members | Search | FAQ
Username:
Password:
Save Password
Forgot your Password?

 All Forums
 MCUmall Forums
 Novice Place
 First time PCB3 User
 New Topic  Reply to Topic
 Printer Friendly
Author Previous Topic Topic Next Topic  

Jim K

USA
5 Posts

Posted - 04/03/2019 :  08:12:29  Show Profile  Reply with Quote
New member, first post. I'm planning to read and program a few 27C512. I have what I believe is the PCB3 programmer (before the PLC sockets), USB cable and P/S wall wart. I've ordered a DB25 cable and PPort card to use with my Win 7/64 box. Downloaded .97ja software and with emulate Win97, it loads and starts perfectly. Configured dip switches and jumpers to match the diagram for the 27C512. While waiting for the parallel port stuff to arrive from Amazon, I was hoping to read an existing 27C512. I installed a programmed 27C512 in the ZIF with pin 1 up and left, but inserted the IC at the bottom of the ZIF socket as shown in the diagram. I get "Hardware Error. Test Power and Connections." Also tried the "Test Hardware" feature from the Help menu and get "Hardware Error. Test Power and Connections." Removed IC and get the same results. Do I need the PPort connections complete and configured before anything will work or am I doing something else wrong? Thanks! Jim
Reply #1

anniel

2531 Posts

Posted - 04/03/2019 :  09:12:17  Show Profile  Reply with Quote
quote:
Originally posted by Jim K

New member, first post. I'm planning to read and program a few 27C512. I have what I believe is the PCB3 programmer (before the PLC sockets), USB cable and P/S wall wart. I've ordered a DB25 cable and PPort card to use with my Win 7/64 box. Downloaded .97ja software and with emulate Win97, it loads and starts perfectly. Configured dip switches and jumpers to match the diagram for the 27C512. While waiting for the parallel port stuff to arrive from Amazon, I was hoping to read an existing 27C512. I installed a programmed 27C512 in the ZIF with pin 1 up and left, but inserted the IC at the bottom of the ZIF socket as shown in the diagram. I get "Hardware Error. Test Power and Connections." Also tried the "Test Hardware" feature from the Help menu and get "Hardware Error. Test Power and Connections." Removed IC and get the same results. Do I need the PPort connections complete and configured before anything will work or am I doing something else wrong? Thanks! Jim

Yes, you need to have your printer port working correctly to use the programmer.
Go to Top of Page
Reply #2

Jim K

USA
5 Posts

Posted - 04/03/2019 :  10:31:23  Show Profile  Reply with Quote
Thanks for the quick response. One last question. As the DB25 on the programmer is male and the connector on the computer LPT port is female, the standard cable with M/F ends will be an "extension" cable meaning the internal wiring will be straight through. Will this be correct for connecting the PCB3? Thanks again. Jim
Go to Top of Page
Reply #3

anniel

2531 Posts

Posted - 04/03/2019 :  14:09:11  Show Profile  Reply with Quote
quote:
Originally posted by Jim K

Thanks for the quick response. One last question. As the DB25 on the programmer is male and the connector on the computer LPT port is female, the standard cable with M/F ends will be an "extension" cable meaning the internal wiring will be straight through. Will this be correct for connecting the PCB3? Thanks again. Jim


Not 100% sure about that, maybe someone who still uses a parallel port could confirm this?
Go to Top of Page
Reply #4

anniel

2531 Posts

Posted - 04/03/2019 :  14:18:09  Show Profile  Reply with Quote
Just looked that up for you. Here's what I found; Parallel Data Cable (Printer extension cable, with male-female 25 pin connector, and pin to pin through)

You may want to have a look here; http://www.mcumall.com/support/DualPoweredWillemUserGuide.htm
Go to Top of Page
Reply #5

Jim K

USA
5 Posts

Posted - 04/03/2019 :  15:25:02  Show Profile  Reply with Quote
anniel - nice catch and thanks for finding that for me. To anyone following this, the answer is yes. The correct cable is a DB25 extension cable meaning that it has a male connector on one end and a female connector on the other end. Pinout /wiring is straight through. Thanks again. Jim
Go to Top of Page
Reply #6

anniel

2531 Posts

Posted - 04/04/2019 :  02:56:15  Show Profile  Reply with Quote
quote:
Originally posted by Jim K

anniel - nice catch and thanks for finding that for me. To anyone following this, the answer is yes. The correct cable is a DB25 extension cable meaning that it has a male connector on one end and a female connector on the other end. Pinout /wiring is straight through. Thanks again. Jim

You're welcome.
Go to Top of Page
Reply #7

Jim K

USA
5 Posts

Posted - 04/05/2019 :  13:13:26  Show Profile  Reply with Quote
OK....so I picked up a P-port card and installed it. Confirmed correct bios setup (ECP+EPP). Set the P-Port in the device manager to port 1 which matches the port selection in .97ja. No conflicts in the device manager. Started the software. Set the programmer to 27C512 and set the dip switches and jumpers as shown in the diagram. Not sure what ICSP (in the diagram) is, but there are no jumpers on the stakes. Connected the DB25, USB and power supply. No IC in the ZIF socket. Restarted software. From Help menu ran "Test Hardware" and I get "HARDWARE ERROR Check power and connection." I've double checked all the above. What am I doing wrong?
Go to Top of Page
Reply #8

Jim K

USA
5 Posts

Posted - 04/05/2019 :  13:21:56  Show Profile  Reply with Quote
P.S. All 3 LEDs are lit. Red, Green and Yellow.
Go to Top of Page
Reply #9

anniel

2531 Posts

Posted - 04/05/2019 :  13:59:50  Show Profile  Reply with Quote
quote:
Originally posted by Jim K

OK....so I picked up a P-port card and installed it. Confirmed correct bios setup (ECP+EPP). Set the P-Port in the device manager to port 1 which matches the port selection in .97ja. No conflicts in the device manager. Started the software. Set the programmer to 27C512 and set the dip switches and jumpers as shown in the diagram. Not sure what ICSP (in the diagram) is, but there are no jumpers on the stakes. Connected the DB25, USB and power supply. No IC in the ZIF socket. Restarted software. From Help menu ran "Test Hardware" and I get "HARDWARE ERROR Check power and connection." I've double checked all the above. What am I doing wrong?

ICSP stands for in-circuit serial programming and should not have jumpers.
All seems right but I'm no PCB3 specialist. Someone more knowledgeable than me on the subject could probably help you better.
Go to Top of Page
Reply #10

anniel

2531 Posts

Posted - 04/05/2019 :  14:01:18  Show Profile  Reply with Quote
quote:
Originally posted by Jim K

P.S. All 3 LEDs are lit. Red, Green and Yellow.

I don't think that's normal. Maybe your programmer is defective?
Go to Top of Page
Reply #11

anniel

2531 Posts

Posted - 04/05/2019 :  14:05:32  Show Profile  Reply with Quote
quote:
Originally posted by anniel

quote:
Originally posted by Jim K

P.S. All 3 LEDs are lit. Red, Green and Yellow.

I don't think that's normal. Maybe your programmer is defective?

Do all the LED stay lit with only power connected?
Go to Top of Page
Reply #12

Temolat05

Nigeria
2 Posts

Posted - 05/29/2019 :  03:18:11  Show Profile  Reply with Quote
I am having similar issues. Could it be that my printer port is faulty or what?

Nothing is Impossible
Go to Top of Page
Reply #13

anniel

2531 Posts

Posted - 05/29/2019 :  04:20:27  Show Profile  Reply with Quote
quote:
Originally posted by Temolat05

I am having similar issues. Could it be that my printer port is faulty or what?

Try it with a printer.
Go to Top of Page
  Previous Topic Topic Next Topic  
 New Topic  Reply to Topic
 Printer Friendly
Jump To:
MCUmall EPROM BIOS Chip Burner Forum © Copyright 2003 - 2009 Mcumall Electronics Inc. Go To Top Of Page
Generated in 0.16 sec. Snitz Forums 2000