MCUmall EPROM BIOS Chip Burner Forum
MCUmall EPROM BIOS Chip Burner Forum
Home | Profile | Register | Active Topics | Members | Search | FAQ
Username:
 Password:
Save Password
Forgot your Password?

 All Forums
 MCUmall Forums
 Using the AVR JTAG ICE and AVRISP ISP programmer
 Compatibility doubt		  New Topic  Reply to Topic
 Printer Friendly
Author Previous Topic Topic Next Topic  

JoseBlik

1 Posts
Posted - 06/06/2008 :  11:21:09  Show Profile  Reply with Quote
Hello, I would like to know if "AVR JTAG ICE and AVRISP ISP programmer" is fully compatible with the original ATMEL JTAGICE MKII and whether AT90USB646 (and similars) con be debbuged with it or not. Thanks in advance.
Reply #1

ZLM

2937 Posts
Posted - 06/11/2008 :  13:01:04  Show Profile  Reply with Quote
Hi,

The "AVR JTAG ICE and AVRISP ISP programmer" does not compatible with JTAGICE MKII.

The JTAGICE MKII is PRG-042 AVR JTAG ICE MKII

see:

http://www.mcumall.com/comersus/store/comersus_viewItem.asp?idProduct=4281
Go to Top of Page
Reply #2

bogy

Japan
4 Posts
Posted - 05/22/2009 :  21:59:15  Show Profile  Reply with Quote
Hi,

I would like to know "PRG-042 AVR JTAG ICE MKII 4-in-1" can use PDI interface for xmega like ATXMEGA128A1 ?
Go to Top of Page
Reply #3

ZLM

2937 Posts
Posted - 05/23/2009 :  16:27:51  Show Profile  Reply with Quote
The PRG-042 aupport XMega chips.

Please see page:
h**p://www.atmel.com/dyn/products/product_card.asp?PN=ATxmega128A3
Go to Top of Page
Reply #4

bogy

Japan
4 Posts
Posted - 05/23/2009 :  17:28:11  Show Profile  Reply with Quote
Does PRG-042 support PDI interface?

Which interface use JTAG and/or PDI for XMEGA by PRG-042?

XMega support two interface, JTAG and PDI.
PDI interface is faster communication speed.
Go to Top of Page
Reply #5

bogy

Japan
4 Posts
Posted - 05/23/2009 :  17:46:23  Show Profile  Reply with Quote
P.S.
Some JTAGICEmkII is not support PDI


h**p://support.atmel.no/knowledgebase/scriptvrstudiohelp/mergedProjects/JTAGICEmkII/mkII/Html/Connecting_to_target_through_the_PDI_interface.htm


Note: Not all JTAGICE mkII units have PDI capabilities. To check whether your JTAGICE mkII is PDI capable, look for the following:

Serial number on underside starts with B0...

Green LED lights inside the encapsulation when a USB connection is made
Go to Top of Page
Reply #6

ZLM

2937 Posts
Posted - 05/26/2009 :  09:32:50  Show Profile  Reply with Quote
There is a green LED in side the box near USB connector. And it will be on when using the USB mode. But no serile on the case since it is not made by Atmel. I think you can return it if it does not work.
Go to Top of Page
Reply #7

bogy

Japan
4 Posts
Posted - 05/27/2009 :  08:30:20  Show Profile  Reply with Quote
Can PRG-042 use atmel's firmware?

h**p://www.atmel.com/dyn/resources/prod_documents/scriptvrisp_mkii_fix.html
Go to Top of Page
Reply #8

ZLM

2937 Posts
Posted - 05/27/2009 :  16:36:21  Show Profile  Reply with Quote
Yes. The PRG-042 uses Atmel firmware. You can update the frimware from AVR Studio IDE software.
Go to Top of Page
  Previous Topic Topic Next Topic  
 New Topic  Reply to Topic
 Printer Friendly
Jump To:
MCUmall EPROM BIOS Chip Burner Forum © Copyright 2003 - 2009 Mcumall Electronics Inc. Go To Top Of Page
Generated in 0.1 sec. Snitz Forums 2000