MCUmall EPROM BIOS Chip Burner Forum
MCUmall EPROM BIOS Chip Burner Forum
Home | Profile | Register | Active Topics | Members | Search | FAQ
Username:
 Password:
Save Password
Forgot your Password?

 All Forums
 MCUmall Forums
 Novice Place
 27c4002 programming problem		  New Topic  Reply to Topic
 Printer Friendly
Author Previous Topic Topic Next Topic  

cp

9 Posts
Posted - 07/12/2009 :  15:45:38  Show Profile  Reply with Quote
Using new GQ-4X and purchased ADP-055 adaptor. purchased new ST M27C4002 chips from Mouser. Installed adaptor. placed orig eprom in zif adpaptor. Jumper J-1 on post 1 & 2. Original eprom reads correctly. has verified checksum. Put in New 27c4002 / blank check / OK and when Write:Writing...
Elapsed time: 0.28 seconds.
Write failed, Address=0x000000, Buffer=0x60 Device=0x00
Write failed
What do I need to do ?
Edited by - cp on 07/12/2009 21:20:17
Reply #1

ZLM

2937 Posts
Posted - 07/12/2009 :  22:27:45  Show Profile  Reply with Quote
can you erase the chip and try again? make sure the pin contacts are good.
Go to Top of Page
Reply #2

cp

9 Posts
Posted - 07/13/2009 :  04:08:10  Show Profile  Reply with Quote
I purchased 6 of the ST M27C4002 (new) from Mouser. Chips are new. Blank checked: OK. So far, tried 4 new M27C4002 eproms...they are all Write / Failed. I'll put them in an eraser...but won't hold my breath.
Go to Top of Page
Reply #3

cp

9 Posts
Posted - 07/13/2009 :  09:25:10  Show Profile  Reply with Quote
I put the new ST M27c4002 eproms. in eprom eraser 1 1/2 hr/ Tried to program them again...Failed:
<<M27C4002>>
ID check skipped
Blank checking...Code Memory
Elapsed time: 3.36 seconds.
Chip is blank
ID check skipped
Writing...
Elapsed time: 0.28 seconds.
Write failed, Address=0x000000, Buffer=0x60 Device=0x00
Write failed
What do I do Now ??
Edited by - cp on 07/13/2009 09:25:33
Go to Top of Page
Reply #4

ZLM

2937 Posts
Posted - 07/13/2009 :  21:19:53  Show Profile  Reply with Quote
The software version should be Re4.02

Can you remove the 10uf capacitor on the adapter and try again?
Go to Top of Page
Reply #5

cp

9 Posts
Posted - 07/14/2009 :  07:46:19  Show Profile  Reply with Quote
Software Version Re4.02 ??? Have no idea what you are talking about. Could you simplify that ? Remove the 10 uf cap ? Is there a design flaw in this adaptor ? I just purchased this adaptor last week. and purchased the GQ-4X 2 months ago. I'll do as you suggest...and remove the cap.
Go to Top of Page
Reply #6

cp

9 Posts
Posted - 07/14/2009 :  09:38:11  Show Profile  Reply with Quote
I removed the 10uf capacitor. reinstalled ver 4.02 / no luck. programmer gave 00000as checksum on orig eprom Read. Found a version 4.03. no luck. What now. ?
Go to Top of Page
Reply #7

ZLM

2937 Posts
Posted - 07/14/2009 :  13:30:09  Show Profile  Reply with Quote
Remove the 10uf cap should not affect the reading. Please check and try it again.
Go to Top of Page
Reply #8

cp

9 Posts
Posted - 07/15/2009 :  06:39:23  Show Profile  Reply with Quote
unplugged GQ-4X programmer. removed adaptor adp-055. turned programmer back on. installed adp-055 onto the GQ-4X. placed original eprom in zif socket on adaptor. checksum: 0000000

now what ?
Go to Top of Page
Reply #9

ZLM

2937 Posts
Posted - 07/15/2009 :  13:23:41  Show Profile  Reply with Quote
Remove the 10uf cap should not affect the reading. There are something wrong with the adapter I think.
Can you try to put the 10uf cap see if it works again? I doubt.
Go to Top of Page
Reply #10

cp

9 Posts
Posted - 07/16/2009 :  09:24:57  Show Profile  Reply with Quote
I put the 10uf cap back in. Put in orig 27c4002 eprom that I'm trying to copy. Read OK. Checksum OK. removed. put in new/erased/blank eprom. Blank check OK. Write: FAILED.

<<M27C4002>>
ID check skipped
Reading...Code Memory
Elapsed time: 3.26 seconds.
Read completed.
ID check skipped
Blank checking...Code Memory
Elapsed time: 3.36 seconds.
Chip is blank
ID check skipped
Writing...
Elapsed time: 0.28 seconds.
Write failed, Address=0x000000, Buffer=0x60 Device=0x00
Write failed

I NEED AND ADAPTOR THAT WILL WORK ! PLS SEND ONE !
Go to Top of Page
Reply #11

ZLM

2937 Posts
Posted - 07/16/2009 :  21:47:50  Show Profile  Reply with Quote
New tested adapter on M27C4002 sent.
Go to Top of Page
  Previous Topic Topic Next Topic  
 New Topic  Reply to Topic
 Printer Friendly
Jump To:
MCUmall EPROM BIOS Chip Burner Forum © Copyright 2003 - 2009 Mcumall Electronics Inc. Go To Top Of Page
Generated in 0.11 sec. Snitz Forums 2000