MCUmall EPROM BIOS Chip Burner Forum
MCUmall EPROM BIOS Chip Burner Forum
Home | Profile | Register | Active Topics | Members | Search | FAQ
Save Password
Forgot your Password?

 All Forums
 MCUmall Forums
 Using The Enhanced/Dual power Willem Programmer
 My ass is on the line ..can somebody please help

Note: You must be registered in order to post a reply.
To register, click here. Registration is FREE!

Format Mode:
Format: BoldItalicizedUnderlineStrikethrough Align LeftCenteredAlign Right Horizontal Rule Insert HyperlinkInsert EmailInsert Image Insert CodeInsert QuoteInsert List Spell Checker

* Forum Code is ON
Smile [:)] Big Smile [:D] Cool [8D] Blush [:I]
Tongue [:P] Evil [):] Wink [;)] Clown [:o)]
Black Eye [B)] Eight Ball [8] Frown [:(] Shy [8)]
Shocked [:0] Angry [:(!] Dead [xx(] Sleepy [|)]
Kisses [:X] Approve [^] Disapprove [V] Question [?]

   Insert an Image File
Check here to include your profile signature.

T O P I C    R E V I E W
vgallardo Posted - 02/08/2006 : 20:14:13
Im trying to program an eprom m27c801 but i keep getting errors,

error at 0x000000 chip = 0xFF buffer= 0x00

this is for a PBX, their incomunicated so you can imagine how important it is for me to get it to work again.
This is what i have to work with: 4-- m27c801 two used two new, one uv eprom eraser, one dual power willem universal programer and about 6 or 8 hours to get it working again.

can anybody please ..please please.. please please please please

i cannot get the programer to work

victor m gallardo
tijuana B.C. Mexico
7   L A T E S T    R E P L I E S    (Newest First)
chaos89-dot-com Posted - 04/01/2006 : 22:45:56
If your refering to measuring the voltage on VPP, would that would be pin 1 of the ZIF socket. I measured voltage on pin 24 when programming and I am only getting 12.25VDC
I measured the voltage on pin 1 of zif and I am only getting 12.49VDC
Not 12.7VDC

How do we up the power to program these eproms without using the 15 voltage setting?

ZLM Posted - 02/10/2006 : 22:40:17
1. "skip write 0xFF" doesn't matter.
2. 12V DC 1amp power adapter more than enough.
3. Please try to increase the tWp to maximume.
4. Remove the chip, and in Test H/W page, check the Vpp-1 check box, and then check if there is a 12.7V Vpp on pin 24 of ZIF.
vgallardo Posted - 02/08/2006 : 22:21:10
i meant 12v dc 1amp

victor m gallardo
tijuana B.C. Mexico
vgallardo Posted - 02/08/2006 : 22:04:52
im using a 12v ac adapter 1000ma, is that ok?
im using the parallel cable.

victor m gallardo
tijuana B.C. Mexico
vgallardo Posted - 02/08/2006 : 22:00:56
when programin should i enable the option "skip write 0xFF"?

victor m gallardo
tijuana B.C. Mexico
vgallardo Posted - 02/08/2006 : 21:56:01
done that and no luck ...the jumpers are fine i cant seem to program the eprom

victor m gallardo
tijuana B.C. Mexico
ZLM Posted - 02/08/2006 : 21:17:10
Please check all the jumper settings. Espacilly on J3, which is just left side of DIP switch. It should be no jumper on it. The jumper is sert on the P1-A19 of JP-1.

For the jumper setting please see:

MCUmall EPROM BIOS Chip Burner Forum © Copyright 2003 - 2009 Mcumall Electronics Inc. Go To Top Of Page
Generated in 0.16 sec. Snitz Forums 2000