MCUmall EPROM BIOS Chip Burner Forum
MCUmall EPROM BIOS Chip Burner Forum
Home | Profile | Register | Active Topics | Members | Search | FAQ
Username:
Password:
Save Password
Forgot your Password?

 All Forums
 MCUmall Forums
 True USB Willem Programmer (GQ-2X,3X,4X & GQ-4x4)
 AM29f032B write error, HELP

Note: You must be registered in order to post a reply.
To register, click here. Registration is FREE!

Screensize:
UserName:
Password:
Format Mode:
Format: BoldItalicizedUnderlineStrikethrough Align LeftCenteredAlign Right Horizontal Rule Insert HyperlinkInsert EmailInsert Image Insert CodeInsert QuoteInsert List Spell Checker
   
Message:

* HTML is OFF
* Forum Code is ON
Smilies
Smile [:)] Big Smile [:D] Cool [8D] Blush [:I]
Tongue [:P] Evil [):] Wink [;)] Clown [:o)]
Black Eye [B)] Eight Ball [8] Frown [:(] Shy [8)]
Shocked [:0] Angry [:(!] Dead [xx(] Sleepy [|)]
Kisses [:X] Approve [^] Disapprove [V] Question [?]

   Insert an Image File
Check here to include your profile signature.
    

T O P I C    R E V I E W
Marcelo Disconzi Posted - 09/08/2016 : 21:26:14
I'm trying to write this IC using a GQ-4X with APD 082, but without success...

AMD29F032B
-90EC
0833DBM H

ID is checked OK (0141), but, the error appears at start of process,0% always, in some cases, I try to erase first, and the erase ends less of one second, something wrong occurs i guess.

I'm trying some ideas, previously discused here, how use a 100nf Z5U cap, or a 2k resistor, but, in both cases, the problem remain. I try too, write lowest (-2), and writes, but at verifies, nothing was write.

If someone can help...
19   L A T E S T    R E P L I E S    (Newest First)
Ice Man Posted - 03/15/2017 : 06:02:06
I have the solution:
To program 29F033C use an external 9V DC power supply as well while programming! It worked fine for me.
Program OK, Verify OK.
Ice Man Posted - 03/10/2017 : 10:04:58
Well, I tried programming with -1 speed, but verify always fails since it doesn't program properly.
I don't know how exactly I'd trace the pins as I don't have any pinouts nor would I know what to check.
Is the 74HC244 really needed at all?

Perhaps, can someone else confirm that the MBM29F033C, AM29F032 and AM29F016 all don't work to program? Or did someone find a way to program them?
anniel Posted - 03/09/2017 : 16:34:19
You can switch individual pins to trace where it goes wrong.
Ice Man Posted - 03/09/2017 : 10:43:53
How would I test it with hardware test function?
anniel Posted - 03/08/2017 : 10:13:44
Maybe you can use the hardware test function of the software to find the fault.
Ice Man Posted - 03/08/2017 : 10:06:37
Just checked. Everything looks clean. :'(
My Programmer is GQ-4X4 with Software 7.11 and USB 3.0 Driver.

Resistors are 2x2.2k and 1x24 Ohm. All work.
Diode show 597 Ohm, so they work, too.
Maybe 74HC244 is faulty? Is it even needed?

Here is pictures of ADP-082:
h**p://share.pho.to/AdX7z
anniel Posted - 03/08/2017 : 09:55:48
Maybe bad solder joints?
Ice Man Posted - 03/08/2017 : 09:24:16
Looks like it. But I don't know where/why.
Tried Jumper V1/V2. Same results.
anniel Posted - 03/08/2017 : 08:58:15
Trouble with the ADP-082?
Ice Man Posted - 03/07/2017 : 09:01:15
Tried MBM29F033C at -2 Speed.
Program 100%, Verify Fail.

AM29F040B TSOP32 works fine. Everything ok.
TSOP40 does not work fine. :(
anniel Posted - 03/07/2017 : 08:48:50
Did you try a slower speed?
Ice Man Posted - 03/07/2017 : 08:26:19
I have the same problem. I can't write AM29F016B or MBM29F033C.
ID Check is correct with jumper set to V2 and 5V.
I'm using ADP-082 with ADP-077 set to TSOP40B.

I try program but every time I get an error about buffer.
I erased the ICs but nothing helps.
Other programmer (TL866) program them fine so it's not a problem of the IC.

What to do?
Marcelo Disconzi Posted - 01/22/2017 : 13:38:59
quote:
Originally posted by ZLM

Have you try the jumper on ADP-082? V1/V2?
Use slower speed?



Yes, I have tried both, if I try to write at any higher speed -2, an error occurs in the first byte, if I try to write at -2, the write arrives at 100%, but, when checking, (3 / 5V) The chip is completely empty, as if there was no recording.
ZLM Posted - 01/21/2017 : 19:40:44
Have you try the jumper on ADP-082? V1/V2?
Use slower speed?
Marcelo Disconzi Posted - 01/18/2017 : 17:22:34
Some idea??

quote:
Originally posted by ZLM

Your programmer is GQ-4x OR GQ-4x4?

Marcelo Disconzi Posted - 09/20/2016 : 20:26:03
quote:
Originally posted by ZLM

Your programmer is GQ-4x OR GQ-4x4?



GQ-4X
ZLM Posted - 09/15/2016 : 20:00:19
Your programmer is GQ-4x OR GQ-4x4?
Marcelo Disconzi Posted - 09/12/2016 : 08:27:01
quote:
Originally posted by ZLM

You chip is not erased.

The chip must be erased before write new data.

Check the chip pin contacting with programmer. Also, change to another chip to try if possible.



Hi ZLM

I have tried more than 4 chips, the problem is the same, I perform the blank check, works fine, but, in some cases, the erase process ends at start.
ZLM Posted - 09/11/2016 : 23:13:48
You chip is not erased.

The chip must be erased before write new data.

Check the chip pin contacting with programmer. Also, change to another chip to try if possible.

MCUmall EPROM BIOS Chip Burner Forum © Copyright 2003 - 2009 Mcumall Electronics Inc. Go To Top Of Page
Generated in 0.08 sec. Snitz Forums 2000