MCUmall EPROM BIOS Chip Burner Forum
MCUmall EPROM BIOS Chip Burner Forum
Home | Profile | Register | Active Topics | Members | Search | FAQ
Username:
Password:
Save Password
Forgot your Password?

 All Forums
 MCUmall Forums
 Open Source Project Willem Programmer Hardware
 If no VPP on Enhanced Willem ....

Note: You must be registered in order to post a reply.
To register, click here. Registration is FREE!

Screensize:
UserName:
Password:
Format Mode:
Format: BoldItalicizedUnderlineStrikethrough Align LeftCenteredAlign Right Horizontal Rule Insert HyperlinkInsert EmailInsert Image Insert CodeInsert QuoteInsert List Spell Checker
   
Message:

* HTML is OFF
* Forum Code is ON
Smilies
Smile [:)] Big Smile [:D] Cool [8D] Blush [:I]
Tongue [:P] Evil [):] Wink [;)] Clown [:o)]
Black Eye [B)] Eight Ball [8] Frown [:(] Shy [8)]
Shocked [:0] Angry [:(!] Dead [xx(] Sleepy [|)]
Kisses [:X] Approve [^] Disapprove [V] Question [?]

   Insert an Image File
Check here to include your profile signature.
    

T O P I C    R E V I E W
usb Posted - 06/02/2005 : 15:23:17
-Confirm your LPT port BIOS setting is EEP mode.
-Makesure the jumper J3 (at the left side of DIP) is shorted the lower two pins. This jumper is switching betwteen the Vpp and A18.

Test all test points on this picture:


The point C should higher than G when Vpp is ON.

To test it, use Test H/W page in software, check and uncheck the Vpp pin1 checkbox in the software, and then measure the all the point voltage.

If your point C voltage is changing when you check-uncheck the Vpp pin 1, then your connection to PC is OK. (The voltage changing must be betwwn 0V and 3.5V above) Otherwise check the connection and the PC LPT port. The point C is directly connected to data cable Pin 1, so, you also can unplug the data cable form the programmer and measure the pin 1 of data cable to confirm the cable is OK.
6   L A T E S T    R E P L I E S    (Newest First)
ZLM Posted - 06/07/2006 : 10:45:47
Great! Many thanks.
YMasquel Posted - 06/06/2006 : 15:11:51
Hello,
If that can help you here is the full refs of IC's.

Image Insert:

85.83 KB

Friendly, Yves.
usb Posted - 01/12/2006 : 23:24:28
I only have one half.

lewinskys Posted - 12/22/2005 : 17:31:11
USB... Can you post the full picture of that board with all the parts labeled? It would be very handy
usb Posted - 09/02/2005 : 16:13:27
It seems your LPT port pin 1 does not provide enough DC current. This
happend on some PCs. Most of PC will solve this issue by changing the PC
BIOS Setting of LPT Mode.

The Point C indicate the DC voltage from LPT port pin 1. To turn on the
Vpp, the point C need to be higher than point G=1.63V.

Your PC only output 1.57V. It just little bit lower than 1.63V.

If the problem still exist after you changed the LPT mode in BIOS. Then
there are couple of ways to solve this issue:

1. Solder a 1K resistor parallel with R1 (See thread picture).OR replace it by a about 500 ohm resister.
2.Replace the R2 with a 4.7K or 5K resistor.

ZLM Posted - 09/02/2005 : 16:11:10
My Enhanced Programmer has no Red Vpp when doing writing. I am measuring from the listed pins to Ground, the measurements are as follows:

VPP ON A=14.24V B=0V C=1.57V D=0V E=0V F=0V G=1.63V
VPP OFF A=14.24V B=0V C=0V D=0V E=0V F=0V G=1.63V

So, what's wrong?

MCUmall EPROM BIOS Chip Burner Forum © Copyright 2003 - 2009 Mcumall Electronics Inc. Go To Top Of Page
Generated in 3.55 sec. Snitz Forums 2000