T O P I C R E V I E W |
cp |
Posted - 07/12/2009 : 15:45:38 Using new GQ-4X and purchased ADP-055 adaptor. purchased new ST M27C4002 chips from Mouser. Installed adaptor. placed orig eprom in zif adpaptor. Jumper J-1 on post 1 & 2. Original eprom reads correctly. has verified checksum. Put in New 27c4002 / blank check / OK and when Write:Writing... Elapsed time: 0.28 seconds. Write failed, Address=0x000000, Buffer=0x60 Device=0x00 Write failed What do I need to do ? |
11 L A T E S T R E P L I E S (Newest First) |
ZLM |
Posted - 07/16/2009 : 21:47:50 New tested adapter on M27C4002 sent. |
cp |
Posted - 07/16/2009 : 09:24:57 I put the 10uf cap back in. Put in orig 27c4002 eprom that I'm trying to copy. Read OK. Checksum OK. removed. put in new/erased/blank eprom. Blank check OK. Write: FAILED.
<<M27C4002>> ID check skipped Reading...Code Memory Elapsed time: 3.26 seconds. Read completed. ID check skipped Blank checking...Code Memory Elapsed time: 3.36 seconds. Chip is blank ID check skipped Writing... Elapsed time: 0.28 seconds. Write failed, Address=0x000000, Buffer=0x60 Device=0x00 Write failed
I NEED AND ADAPTOR THAT WILL WORK ! PLS SEND ONE !
|
ZLM |
Posted - 07/15/2009 : 13:23:41 Remove the 10uf cap should not affect the reading. There are something wrong with the adapter I think. Can you try to put the 10uf cap see if it works again? I doubt. |
cp |
Posted - 07/15/2009 : 06:39:23 unplugged GQ-4X programmer. removed adaptor adp-055. turned programmer back on. installed adp-055 onto the GQ-4X. placed original eprom in zif socket on adaptor. checksum: 0000000
now what ? |
ZLM |
Posted - 07/14/2009 : 13:30:09 Remove the 10uf cap should not affect the reading. Please check and try it again.
|
cp |
Posted - 07/14/2009 : 09:38:11 I removed the 10uf capacitor. reinstalled ver 4.02 / no luck. programmer gave 00000as checksum on orig eprom Read. Found a version 4.03. no luck. What now. ? |
cp |
Posted - 07/14/2009 : 07:46:19 Software Version Re4.02 ??? Have no idea what you are talking about. Could you simplify that ? Remove the 10 uf cap ? Is there a design flaw in this adaptor ? I just purchased this adaptor last week. and purchased the GQ-4X 2 months ago. I'll do as you suggest...and remove the cap. |
ZLM |
Posted - 07/13/2009 : 21:19:53 The software version should be Re4.02
Can you remove the 10uf capacitor on the adapter and try again? |
cp |
Posted - 07/13/2009 : 09:25:10 I put the new ST M27c4002 eproms. in eprom eraser 1 1/2 hr/ Tried to program them again...Failed: <<M27C4002>> ID check skipped Blank checking...Code Memory Elapsed time: 3.36 seconds. Chip is blank ID check skipped Writing... Elapsed time: 0.28 seconds. Write failed, Address=0x000000, Buffer=0x60 Device=0x00 Write failed What do I do Now ?? |
cp |
Posted - 07/13/2009 : 04:08:10 I purchased 6 of the ST M27C4002 (new) from Mouser. Chips are new. Blank checked: OK. So far, tried 4 new M27C4002 eproms...they are all Write / Failed. I'll put them in an eraser...but won't hold my breath. |
ZLM |
Posted - 07/12/2009 : 22:27:45 can you erase the chip and try again? make sure the pin contacts are good. |