| T O P I C R E V I E W |
| ianlill |
Posted - 12/12/2018 : 11:58:48
i keep getting this message no matter what i do have tried 2 ecu same problem device blank check failed at address 0x0000 10 read =0x05 can you help |
| 31 L A T E S T R E P L I E S (Newest First) |
| anniel |
Posted - 01/03/2019 : 11:14:26
quote:
Originally posted by ianlill
all ok on continuity check
Do an Hardware I/O Diagnostics on your GQ-4X4 to rule it out. |
| ianlill |
Posted - 01/03/2019 : 10:47:36
all ok on continuity check |
| anniel |
Posted - 01/03/2019 : 10:15:39
quote:
Originally posted by ianlill
Failed,address =0x000000,devise=oxFF,buffer=ox12 WHAT IS THAT TELLING ME so i can understand
It is telling you just that. Your write failed at address 0x000000, the device reads 0xFF and the buffer is 0x12. |
| anniel |
Posted - 01/03/2019 : 10:11:27
quote:
Originally posted by ianlill
DONE THAT NO 5 VOLTS ON CLIP
You are not looking for 5V. You need to do a continuity check. What make and model is your multimeter? |
| ianlill |
Posted - 01/03/2019 : 09:59:58
Failed,address =0x000000,devise=oxFF,buffer=ox12 WHAT IS THAT TELLING ME so i can understand |
| ianlill |
Posted - 01/03/2019 : 09:57:23
DONE THAT NO 5 VOLTS ON CLIP
|
| anniel |
Posted - 01/03/2019 : 09:30:10
quote:
Originally posted by ianlill
how do you do that
Multimeter. |
| ianlill |
Posted - 01/03/2019 : 09:24:42
how do you do that |
| anniel |
Posted - 01/03/2019 : 09:17:59
quote:
Originally posted by ianlill
it is done via a clip that goes on the chip
Did you test for good continuity from chip to ZIF? |
| ianlill |
Posted - 01/03/2019 : 09:14:50
it is done via a clip that goes on the chip |
| anniel |
Posted - 01/03/2019 : 09:10:15
quote:
Originally posted by ianlill
same problem
Is this a DIP or does it need an adapter? |
| ianlill |
Posted - 01/03/2019 : 09:07:32
same problem
|
| anniel |
Posted - 01/03/2019 : 09:03:22
quote:
Originally posted by ianlill
no its on my ecu what is it telling me when i get Failed,address =0x000000,devise=oxFF,buffer=ox12
Ok, pull the chip off the board and try again. |
| ianlill |
Posted - 01/03/2019 : 08:59:54
no its on my ecu what is it telling me when i get Failed,address =0x000000,devise=oxFF,buffer=ox12 |
| anniel |
Posted - 01/03/2019 : 08:51:21
quote:
Originally posted by ianlill
Sorry its M95040
Is it pulled off the board? |
| ianlill |
Posted - 01/03/2019 : 08:47:57
Sorry its M95040 |
| anniel |
Posted - 01/03/2019 : 08:43:00
quote:
Originally posted by ianlill
used M95040 it blanks,go to write then get the Failed,address =0x000000,devise=oxFF,buffer=ox12
Is your device a M95404 like you said earlier or a M95040? |
| ianlill |
Posted - 01/03/2019 : 08:35:18
used M95040 it blanks,go to write then get the Failed,address =0x000000,devise=oxFF,buffer=ox12 |
| anniel |
Posted - 01/03/2019 : 08:28:51
quote:
Originally posted by ianlill
gq-4x4
Ok and which part number did you use in the device list?
|
| ianlill |
Posted - 01/03/2019 : 08:24:12
gq-4x4 |
| anniel |
Posted - 01/03/2019 : 07:14:24
quote:
Originally posted by ianlill
do you mean this number m95404
What programmer do you use? |
| ianlill |
Posted - 01/03/2019 : 07:03:34
do you mean this number m95404 |
| anniel |
Posted - 01/03/2019 : 06:54:12
quote:
Originally posted by ianlill
yes
What is the part number? |
| ianlill |
Posted - 01/03/2019 : 00:40:10
yes |
| anniel |
Posted - 01/02/2019 : 16:01:17
quote:
Originally posted by ianlill
failed,address =0x000000,devise=oxFF,buffer=ox12
get the above
Probably damaged. Did you use the same part number in the device list? |
| ianlill |
Posted - 01/02/2019 : 12:58:11
failed,address =0x000000,devise=oxFF,buffer=ox12
get the above |
| anniel |
Posted - 01/02/2019 : 12:41:52
quote:
Originally posted by ianlill
its blanked but wont write
So now they pass the blank check but simply refuse to write? Do you get an error message? |
| ianlill |
Posted - 01/02/2019 : 12:24:42
its blanked but wont write |
| anniel |
Posted - 01/02/2019 : 12:04:49
quote:
Originally posted by ianlill
yes wont write
If your devices doesn't pass the blank check they are not erased correctly or damaged. |
| ianlill |
Posted - 01/02/2019 : 11:50:29
yes wont write |
| anniel |
Posted - 12/13/2018 : 04:30:41
quote:
Originally posted by ianlill
i keep getting this message no matter what i do have tried 2 ecu same problem device blank check failed at address 0x0000 10 read =0x05 can you help
Did you erase them? |
